){kind=link}
4″ x 3″ DECK & DOCK LIGHT – 14 Pack Kit – (Actual size: 4 3/4″ x 3 3/4″ x 2″ thick) The Deck and Dock Lights are an exciting breakthrough in exterior illumination. They will give your wooden or Terx deck and dock areas the necessary directional lighting, as well as an attractive, sophisticated appearance. These lights not only enhance the look of your property, but also provide you with additional security and when used in appropriate areas, they can enhance the safety of your loved ones and guests. The 3″ x 4″ DECK LIGHT is designed for easy installation into wood or trex decking. A small notch is cut out of adjoining deck boards, and then the light is inserted and locked in place with hold-tight tabs. The wide lip supports the light and its smooth, rounded corners make the DECK LIGHT a safe, yet elegant addition to your outdoor living area. Each 14 light kit contains (14) DECK LIGHT fixtures & lenses, (14) sockets, (14) 4-watt bulbs, (28) wire connectors, 100 feet of 16/2 outdoor cable, 100-Watt transformer and instructions. The supplied 12-volt dust-to-dawn 100-Watt transformer can power up to 25 – 4-watt fixtures. Add-on lights are also available on out TJB-INC Amazon Store (additional cable may be necessary depending on number and spacing of lights). Tools Required: Jig Saw, Pliers, Utility Knife, & Regular Screwdriver. The DECK & DOCK Lights can be used in wet areas like docks, porches, wood stairs, & decks. Use them to highlight borders and add safety to a dark area. The clear bulbs can be easily changed out and replaced with colored bulbs like red, yellow, green, or red (all available separately) for special effects. They come with a 2 year manufacturer warranty.
Product Features
- Add Lights to a Deck, Dock, Porch, or Wood Stairs
- 2 Year Warranty
- Includes 12 volt Transformer to power lights
- Available individually or in kits as well
- Other Sizes & Styles Available on our TJB-INC Amazon Store
Related posts:
Kerr Lighting Deck Lights – 4″ x 3″ – 8-Pack Kit – For Decks, Docks, & Stairs
Kerr Lighting Deck Lights – 4″ x 3″ – 4 Pack Add On – For Decks, Docks & Stairs
Kerr Lighting Deck Light (4″ X 3″) (Individual) – For Decks, Docks, & Stairs
Kerr Lighting Residential Paver Lights 4″ x 8″ for Walk, Patio, Driveway, & Pool Deck Installation , 14 Pack Installation Kit
Kerr Lighting Residential Paver Lights 4″ x 8″ for Walk, Patio, Driveway, & Pool Deck Installation , 8 Pack Installation Kit
Kerr Lighting 12 vt BC Paver Light – 4 1/2″ x 9″ for Walk, Patio, Driveway, & Pool Deck Installation , 14 Pack Installation Kit
Very Nice Product I installed these on a deck with 5/4 decking.First I laid them out with even spacing (~6 ft apart) and traced them with a pencil. I was worried about weakening the integrity of the deck, so I placed them near a floor joist and evenly spaced between two adjoining deck boards.Then I drilled all four corners using a spade bit, finishing them up with a saber saw. The deck stayed absolutely solid.After I had the holes cut, i laid out the wire under the deck by eyeballing the holes above. Back up top, I used a ‘snake’ to retrieve the wire to install the connectors. Once the wire is through the hole and slack taken out of it, use a vice grip on each side of where your cut will be to stop the wire from falling back through. One person installation was easy enough.The connecters were a dream. I love the lights and controller.I’d buy these again and have already recommended them to several friends.
deck lites not as heavyas I would have liked but for the price great, the timer works great and eazy to install
Typical as Usual Here are the facts.1-Transformer pictured was not what I received, the replacement works fine.2-Do not use the light cover for a template as directed, you will have 14 holes that are too small. Fortunately, I tried it first on what I was going to use as a template, I would recommend you do the same.3-The plastic clips that are to hold the fixture in place are NOT designed for 5/4 decking, they are for 2X only. I had to drill holes inside the fixture and nail them in place.4-Make sure you understand the wiring, if there is any doubt, it is because the directions are vague as to the purpose.5-The connectors will take some serious force to connect the wires, if they are not fully compressed you will find yourself going back to do it right the second time.All in all, I am happy with the finished product, although I do feel I overpaid for what I got.
Comments are disabled for this post.